DREVOZAKHYST LASUR Wood Lacquer-Antiseptic

Save to favorites

Compare

DREVOZAKHYST LASUR Wood Lacquer-Antiseptic

4.3 (3)

A "3 in 1" alkyd lazure. Impregnation and varnish in one A tough elastic film The colour of fine timbers UV-stable pigments

Specifications

Consumption:
80–100 g/m² per coat
Storage term:
18 months
Drying time:
24 hours between coats
Application area:
Indoor and outdoor use
Number of coats:
2–3
Thinner:
White spirit
Application temperature:
+5…+30 °C

Choose a variant

Color: Golden pine Rosewood Chestnut Dark oak Teak Walnut
Packaging: 0.7 kg 2 kg

Calculated for one coat at the average rate of 90 g/m² (range 80–100 g/m²).

DREVOZAKHYST LASUR by POLIFARB is a coloured alkyd lazure for protecting and finishing timber and wood-based surfaces.

Impregnation and varnish in one tin

Literally "3 in 1": the formulation combines an impregnation with a varnish. The classic sequence (antiseptic treatment first, then varnish) needs two products, two drying cycles and twice the labour. Here both steps happen at once.

A film, not just penetration

Unlike a pure impregnation, the lazure forms a tough, elastic film that takes the mechanical and weather load while leaving the grain visible.

Weather resistance

Weather-resistant against ageing, moisture and UV, with antiseptics in the formulation to protect the timber. Unlike the IMPREGNAT impregnation, the lazure gives a sealed surface and a deeper, richer colour. Satin-matt finish. For better protection outdoors, one coat of clear IMPREGNAT impregnation is recommended first.

Six shades

Golden pine, teak, dark oak, chestnut, walnut and rosewood, with UV-stable pigments.

Where it is used

Timber facades, gazebos, fences, garden furniture and other structures indoors and out; plywood, hardboard, chipboard and MDF exposed to weather, moisture and UV.

Conditions

Thin with white spirit. Two or three coats, 80–100 g/m² per coat, the next coat after 24 hours. Brush, roller or spray along the grain at +5 to +30 °C and humidity no more than 60%. Clean tools with white spirit. The lazure is flammable. 0.7 kg and 2.2 kg, 18-month shelf life, do not freeze.

How much you need

Example: how much area one package covers in one coat at 80–100 g/m².

  • 700 g — 7–8.8 m²
  • 2 kg — 20–25 m²

Application

Preparation

  • strip flaking coatings and the weathered grey layer;

  • sand along the grain and dust off;

  • moisture content no higher than 20 %;

  • treat any affected areas separately first.

Application

  • stir; thin with white spirit if needed;

  • brush along the grain, or roll or spray;

  • two or three coats, each after the last has dried;

  • up to 24 hours between coats.

For even colour

  • test on an offcut of the same timber: the shade depends on species and coats;

  • each coat deepens the colour;

  • work a piece end to end without stopping, or the join will show.

Afterwards

  • clean tools with white spirit;

  • spread out and dry soaked rags;

  • seal the tin; 18 months, away from flame.

FAQ: lazure or impregnation, coats and colour

  • Lazure or IMPREGNAT?
    The impregnation lasts longer, 8 years against 5, and forms no film; the lazure gives a tough film, deeper colour and a sealed surface. For the best result, impregnate first and lazure over it.

  • What does "3 in 1" mean?
    Impregnation and varnish are combined, so two separate products are not needed.

  • Will the grain show?
    Yes. It tints the timber rather than covering it.

  • How many coats on a fence?
    Three.

  • Thinner and clean-up?
    White spirit; it does not thin with water.

No videos have been added for this product yet.

Customer reviews

Пчеловод

Лакирую очень часто свои улики.Нареканий пока нет.

Алла

Очень красивый цвет темный дуб.

Лиза

Очень блестит после высыхания.Думала что блеск будет меньше.

Write a review

Rating