Selected package
Leftover:
We use necessary cookies for the cart, session, and security. Analytics and marketing cookies are enabled only after your choice. Learn more
Polifarb App
Add the store to your home screen for faster access and an app-like full-screen experience.
It installs in a couple of taps — here is how.
Tap in the Safari toolbar
Choose “Add to Home Screen”
To install the app, open this site in the Safari browser.
Search
Start typing to see suggestions.
Save to favorites
Add to compare
A "3 in 1" alkyd lazure. Impregnation and varnish in one A tough elastic film The colour of fine timbers UV-stable pigments
12 available
Calculated at the average rate of 90 g/m² per coat (data sheet range 80–100 g/m²). Coats: 3.
Selected package
Leftover:
Cheaper package combination
pcs
Leftover:
DREVOZAHYST LASUR by POLIFARB is a coloured alkyd lazure for protecting and finishing timber and wood-based surfaces.
Literally "3 in 1": the formulation combines an impregnation with a varnish. The classic sequence (antiseptic treatment first, then varnish) needs two products, two drying cycles and twice the labour. Here both steps happen at once.
Unlike a pure impregnation, the lazure forms a tough, elastic film that takes the mechanical and weather load while leaving the grain visible.
Weather-resistant against ageing, moisture and UV, with antiseptics in the formulation to protect the timber. Unlike the IMPREGNAT impregnation, the lazure gives a sealed surface and a deeper, richer colour. Satin-matt finish. For better protection outdoors, one coat of clear IMPREGNAT impregnation is recommended first.
Golden pine, teak, dark oak, chestnut, walnut and rosewood, with UV-stable pigments.
Timber facades, gazebos, fences, garden furniture and other structures indoors and out; plywood, hardboard, chipboard and MDF exposed to weather, moisture and UV.
Thin with white spirit. Two or three coats, 80–100 g/m² per coat, the next coat after 24 hours. Brush, roller or spray along the grain at +5 to +30 °C and humidity no more than 60%. Clean tools with white spirit. The lazure is flammable. 0.7 kg and 2.2 kg, 18-month shelf life, do not freeze.
How much you need
90 g/m² per coat; budget three coats, about 270 g/m².
700 g covers about 2.5 m²: garden furniture, a door, a window frame;
2 kg covers about 7.5 m²: a fence bay or a small gazebo.
Typical areas:
a garden table with benches: 4–6 m²;
a 3×3 m gazebo with roof, about 30 m²: 8 kg;
20 m of 1.5 m fence, both sides, 60 m²: 16 kg.
Time matters too. Up to 24 hours between coats against the 16 hours of IMPREGNAT, so three coats means three days: plan for a dry spell, not a weekend between showers.
Application
Preparation
strip flaking coatings and the weathered grey layer;
sand along the grain and dust off;
moisture content no higher than 20 %;
treat any affected areas separately first.
Application
stir; thin with white spirit if needed;
brush along the grain, or roll or spray;
two or three coats, each after the last has dried;
up to 24 hours between coats.
For even colour
test on an offcut of the same timber: the shade depends on species and coats;
each coat deepens the colour;
work a piece end to end without stopping, or the join will show.
Afterwards
clean tools with white spirit;
spread out and dry soaked rags;
seal the tin; 18 months, away from flame.
FAQ: lazure or impregnation, coats and colour
Lazure or IMPREGNAT?
The impregnation lasts longer, 8 years against 5, and forms no film; the lazure gives a tough film, deeper colour and a sealed surface. For the best result, impregnate first and lazure over it.
What does "3 in 1" mean?
Impregnation and varnish are combined, so two separate products are not needed.
Will the grain show?
Yes. It tints the timber rather than covering it.
How many coats on a fence?
Three.
Thinner and clean-up?
White spirit; it does not thin with water.