We use necessary cookies for the cart, session, and security. Analytics and marketing cookies are enabled only after your choice. Learn more
Polifarb App
Add the store to your home screen for faster access and an app-like full-screen experience.
It installs in a couple of taps — here is how.
Tap in the Safari toolbar
Choose “Add to Home Screen”
To install the app, open this site in the Safari browser.
Catalog
Popular categories
Search
Start typing to see suggestions.
Save to favorites
Add to compare
Alkyd-urethane enamel for wood and metal. A very hard gloss finish Over 10 years of protection Dry in 3 hours
30 available
Calculated at the average rate of 45 g/m² per coat (data sheet range 30–60 g/m²). Coats: 2.
Selected package
Leftover:
Cheaper package combination
pcs
Leftover:
DEKOLUX is a premium alkyd-urethane enamel for protecting primed wood and wood-based surfaces, metal and other substrates.
The urethane component makes the film far harder than plain alkyd. The coating takes mechanical load where an ordinary enamel wears through: machinery, equipment, handrails, gates. The declared protection is over 10 years.
A coat dries in 3 hours against 24 for alkyd PF-115. The second coat goes on once the first is fully dry, no sooner than 5 hours later, so two coats fit into one day. The film reaches full hardness after 7 days.
30–60 g/m² per coat is a third of what floor enamels use and half of EXTRAMAL PF-115.
Steelwork, agricultural machinery, freight vehicles, railway carriages: anywhere the coating has to take weather and wear and still look right. The enamel holds both its colour and its gloss instead of dulling in the first season.
A ready range of 14 shades, from cream and yellow to dark green and black, tintable with COLOR MIX pastes. Sheen: high gloss. Thinned with white spirit, solvent naphtha or a 1:1 mix of the two, no more than 10% by volume. Bare wood is primed with Drevozakhyst impregnant or drying oil, unprotected metal with DEKOMAL GF-021; let the primer dry at least 24 hours before the enamel. Blast-cleaned metal should be painted within 8–10 hours of cleaning. Apply 1–2 coats at air and substrate temperature of +5…+30 °C and relative humidity up to 60%. The enamel is flammable: ventilate and keep away from open flame. Shelf life 24 months.
How much you need
45 g/m² per coat over two coats: 90 g/m² in total, the lowest consumption among the enamels in this category.
700 g covers about 8 m²: a gate, handrails, a small structure;
2 kg covers about 22 m²: a garage interior or a trailer body;
16 kg covers about 175 m²: farm machinery or a batch of steelwork.
Application
Preparing the surface
strip metal of rust, scale and flaking old coating;
sand and dust off timber;
prime the surface: the enamel is meant for primed substrates;
degrease with white spirit or solvent.
Thinning
thin with white spirit to working viscosity if needed;
more for spraying, barely any for brushwork;
stir thoroughly before use.
Application
apply by brush, roller or spray;
1–2 coats depending on how contrasting the substrate is;
a coat dries in up to 3 hours: the second goes on the same day.
After the job
clean tools with white spirit straight away;
store tightly closed away from flame;
shelf life 24 months.
FAQ: hardness, consumption and substrates
How does it differ from ordinary PF enamel?
The urethane component: a harder film, 3 hours to dry instead of a day, over 10 years of service instead of 4–5, and half the consumption.
Can it go straight over rust?
No, this enamel needs a primed surface. For bare rust use the "Zahyst 3 v 1" primer-enamel.
How much for a 3×2 m gate?
Both sides come to 12 m²; two coats need about 1.1 kg, so a 2 kg tin with a margin.
What thins it and cleans the tools?
White spirit. Alkyd-urethane enamel does not thin with water.
Does the colour fade in the sun?
The enamel holds its colour and gloss for a long time: that is one of its declared properties.
3 similar products
Color
Packaging
from
281.00 ₴
224.80 ₴
Color
Packaging
from
288.00 ₴
230.40 ₴
