Selected package
pcs
Leftover:
Save to favorites
Compare
DREVOZAKHYST IMPREGNAT Antiseptic Wood Preservative
An alkyd impregnation that enters the fibres instead of sitting on top. Protection against fungi, insects and mould Eight shades Thinned with white spirit
Specifications
- Consumption:
- 80–100 g/m² per coat
- Storage term:
- 18 months
- Drying time:
- 8 hours between coats
- Application area:
- Indoor and outdoor use
- Number of coats:
- 2–3
- Thinner:
- White spirit
- Application temperature:
- +5…+30 °C
Choose a variant
Calculated for one coat at the average rate of 90 g/m² (range 80–100 g/m²).
Scope
Material needed
Total
Cheaper package combination
pcs
Leftover:
DREVOZAKHYST IMPREGNAT by POLIFARB is an alkyd impregnation for the decorative and protective treatment of timber and wood-based surfaces, indoors and out.
An impregnation, not a coating
The key difference from lazures and varnishes: it soaks deep into the timber and polymerises inside the fibres rather than forming a film on top. A film eventually peels, and what it was meant to prevent starts underneath; an impregnation has nothing to peel from. It is not a finish coat, though: once dry, the surface is protected with pentaphthalic varnish, 1–2 coats for items used indoors and 2–3 coats for items exposed to weather. Indoor floors are treated only in combination with varnishes.
Three threats
The impregnation protects timber against fungi, insects and mould, and against rain and temperature swings.
The colour of fine timbers
Eight options: clear, pine, teak, oak, mahogany, walnut, wenge and classic rosewood. The pigments are UV-stable and the colour is durable.
It still breathes
The treatment does not block vapour permeability, so log walls, gazebos and cladding keep releasing moisture rather than storing it.
Where it is used
Timber facades, log houses, gazebos, fences, furniture, windows, doors, cladding, skirting, natural timber panels, plywood, OSB, MDF, chipboard and hardboard, and the outside of beehives.
Conditions
Stir thoroughly before use; thin with white spirit. No primer needed. Two or three coats, 80–100 g/m² per coat, the next coat after 8 hours. Apply with a soft brush, pad or sponge along the grain; do not spray. Air and substrate +5 to +30 °C, humidity no more than 60%. Clean tools with white spirit. The impregnation is flammable. 18-month shelf life, do not freeze. Packed in 0.7 kg.
How much you need
Example: how much area one package covers in one coat at 80–100 g/m².
- 700 g — 7–8.8 m²
Application
Preparation
clean off dirt, old coatings and the weathered grey layer;
sand and dust off;
moisture content no higher than 20 %: it will not enter wet timber;
no primer needed.
Application
stir; do not thin;
brush along the grain, or use a pad or sponge;
two or three coats, each after the last has dried;
up to 16 hours between coats at +20 °C, longer when cold.
Where to be generous
end grain: the main route for water;
the bottom courses of a log wall and anything near the ground;
joints, grooves and fixings where moisture lingers.
Afterwards
clean tools with white spirit;
spread out and dry any soaked rags rather than leaving them balled up;
seal the tin; 18 months.
FAQ: impregnation or lazure, coats, end grain
Versus DREVOZAKHYST LASUR?
Mechanism. This soaks in and forms no film, lasting over 8 years; the lazure leaves a tough elastic film and lasts over 5. They are often combined: impregnation first, lazure for appearance.Primer needed?
No, it primes itself.How many coats?
Two or three; three outdoors.Beehives?
The outside only, as the maker states.New untreated boards?
Ideal. Dry planed timber takes it evenly.
No videos have been added for this product yet.
Customer reviews
Денис
пропитка работает,но нужно сверху еще лазуоью покрывать.
Write a review
Similar products
1 similar products
-15%
