Selected package
pcs
Leftover:
Save to favorites
Compare
60 seconds professional adhesive foam
Fast-grab adhesive foam. Tack-free in 3–5 minutes Set in 5–30 The next row of boards goes up without waiting
Specifications
- Curing time:
- 5 - 30 minutes*
- Full polymerization time:
- 12 - 48 hours*
- Maximum joint depth:
- 30 mm
- Storage term:
- 18 months
- Tack-free time:
- 3 - 5 minutes*
- Cylinder temperature:
- +15°C ... +30°C
- Secondary expansion:
- 100 - 150%*
- Base:
- foamed polyurethane composition
- Application temperature:
- -5°C ... +35°C
Choose a variant
Maximum joint depth: 30 mm
Scope
Material needed
Total
Cheaper package combination
pcs
Leftover:
"60 seconds" adhesive foam is a professional gun-applied polyurethane adhesive for insulation boards, with accelerated grab.
Speed is the point
Ordinary adhesive foam goes tack-free in 5–30 minutes and fixes a board in a couple of hours. This one is tack-free in 3–5 minutes and sets in 5–30. Rows need no propping, and the next one follows almost at once.
Where that speed matters
Vertical and overhead work: cellar ceilings, garage slabs and plinths, where a board slides under its own weight while the adhesive gains strength. Where boards sit on a starter rail, ordinary adhesive foam is enough.
The trade-off
There is almost no time to correct. Ordinary adhesive foam allows up to 15 minutes; here the board must be placed right first time. Mark out and cut beforehand.
Low expansion
100–150 % secondary expansion, less than household foams, so boards stay against the wall. Still allow for lift and check each row with a straightedge.
Other uses
Besides insulation boards, the manufacturer lists it for work with aerated concrete and foam concrete blocks and for sealing joints, indoors and out.
Conditions
Apply at -5 to +35 °C, can at +15 to +30 °C. Full cure 12–48 hours: do not anchor or load sooner despite the fast grab. 800 ml, gun only, 18-month shelf life.
Limits
No UV resistance; always cover the insulation. Flush the gun immediately after work.
How much you need
An 800 ml can covers about 10–12 m².
- a 20 m² cellar ceiling: two cans;
- a 6×4 m garage slab: 24 m², two and a half cans;
- a plinth around a 10×8 m house, 0.5 m high: 18 m²;
- reveals and small areas: one can for several windows.
On a 1000×1000 mm board: a Ø30 mm perimeter bead 2–3 cm in plus a central bead, about 4.5 m per board. Bead no more than two or three boards ahead, or the foam will skin before they are placed.
Application
All preparation up front
- clean, dry and prime the substrate;
- mark and cut every board beforehand;
- bring the can to +15–30 °C and shake;
- fit it to the gun.
Application
- a Ø30 mm perimeter bead 2–3 cm in plus a central bead;
- bead no more than two or three boards ahead;
- wait 1–2 minutes and place;
- place accurately first time: after 3–5 minutes it will not move.
Checking
- straightedge every row immediately;
- set in 5–30 minutes, so there is no time to correct;
- fill board joints with the same foam.
Then
- anchor after full cure, 12–48 hours;
- trim once set;
- cover with the reinforced coat;
- flush the gun at once.
FAQ: speed, correction and anchors
Does it really grab in 60 seconds?
The name reflects initial grab; the rated figures are tack-free in 3–5 minutes, set in 5–30, full cure 12–48 hours.When to choose it?
When boards slide: ceilings, slabs, plinths without a starter rail.Correction time?
Effectively none. Place it right first time.When can anchors go in?
After full cure, 12–48 hours.Below zero?
From -5 °C, narrower than the -10 °C of the standard adhesive foam.
No videos have been added for this product yet.
Customer reviews
Ruslan
Хорошая пена.
Write a review
Similar products
6 similar products
-
NEW
-
-
-
-15%
-
-
