60 seconds professional adhesive foam

Save to favorites

Add to compare

Sale ends in

00 days
00 hrs
00 min
00 sec

60 seconds professional adhesive foam, Turquoise, 800 ml

5.0 (1)

Fast-grab adhesive foam. Tack-free in 3–5 minutes Set in 5–30 The next row of boards goes up without waiting

Specifications

Color:
Turquoise
Curing time:
5 - 30 minutes*
Full polymerization time:
12 - 48 hours*
Maximum joint depth:
30 mm
Storage term:
18 months
Tack-free time:
3 - 5 minutes*
Cylinder temperature:
+15°C ... +30°C
Secondary expansion:
100 - 150%*
Packaging:
800 ml
Base:
foamed polyurethane composition
Application temperature:
-5°C ... +35°C

Choose a variant

1 available

Color: Turquoise Turquoise
Packaging: 800 ml

Consumption calculator

Maximum joint depth: 30 mm

Selected variant Turquoise · 800 ml

272.85 ₴

Description

"60 seconds" adhesive foam is a professional gun-applied polyurethane adhesive for insulation boards, with accelerated grab.

Speed is the point

Ordinary adhesive foam goes tack-free in 5–30 minutes and fixes a board in a couple of hours. This one is tack-free in 3–5 minutes and sets in 5–30. Rows need no propping, and the next one follows almost at once.

Where that speed matters

Vertical and overhead work: cellar ceilings, garage slabs and plinths, where a board slides under its own weight while the adhesive gains strength. Where boards sit on a starter rail, ordinary adhesive foam is enough.

The trade-off

There is almost no time to correct. Ordinary adhesive foam allows up to 15 minutes; here the board must be placed right first time. Mark out and cut beforehand.

Low expansion

100–150 % secondary expansion, less than household foams, so boards stay against the wall. Still allow for lift and check each row with a straightedge.

Conditions

Apply at -5 to +35 °C, can at +15 to +30 °C. Full cure 12–48 hours: do not anchor or load sooner despite the fast grab. 800 ml, gun only, 18-month shelf life.

Limits

No UV resistance; always cover the insulation. Flush the gun immediately after work.

How much you need

An 800 ml can covers about 10–12 m².

  • a 20 m² cellar ceiling: two cans;
  • a 6×4 m garage slab: 24 m², two and a half cans;
  • a plinth around a 10×8 m house, 0.5 m high: 18 m²;
  • reveals and small areas: one can for several windows.

On a 1000×1000 mm board: a Ø30 mm perimeter bead 2–3 cm in plus a central bead, about 4.5 m per board. Bead no more than two or three boards ahead, or the foam will skin before they are placed.

Application

All preparation up front

  • clean, dry and prime the substrate;
  • mark and cut every board beforehand;
  • bring the can to +15–30 °C and shake;
  • fit it to the gun.

Application

  • a Ø30 mm perimeter bead 2–3 cm in plus a central bead;
  • bead no more than two or three boards ahead;
  • wait 1–2 minutes and place;
  • place accurately first time: after 3–5 minutes it will not move.

Checking

  • straightedge every row immediately;
  • set in 5–30 minutes, so there is no time to correct;
  • fill board joints with the same foam.

Then

  • anchor after full cure, 12–48 hours;
  • trim once set;
  • cover with the reinforced coat;
  • flush the gun at once.

FAQ: speed, correction and anchors

  • Does it really grab in 60 seconds?
    The name reflects initial grab; the rated figures are tack-free in 3–5 minutes, set in 5–30, full cure 12–48 hours.

  • When to choose it?
    When boards slide: ceilings, slabs, plinths without a starter rail.

  • Correction time?
    Effectively none. Place it right first time.

  • When can anchors go in?
    After full cure, 12–48 hours.

  • Below zero?
    From -5 °C, narrower than the -10 °C of the standard adhesive foam.

Video
Reviews (1)

Similar products

4 similar products